04
Jul
Wire crimping machine refers to a kind of machine used in wire processing. It can crimp metal terminal to the wire end and then make conduction. The terminals crimped by the wire terminator crimping machine are usually for the convenience of connection. Without welding, the two wires can be connected together steadily, and only need to be pulled out when disassembling.
1. The motor keeps turning. There is an internal wrapped breaker with a clutch, every move generates a standard “O” out, which is the most common.
2. In the last five years, mute wire crimping machine with servo have appeared. Their operating principles are different from those above. They just give the servo a message, which is then transmitted to the motor and acts as an action.
3. Terminal crimping and excellent quality products.
Automatic wire crimping machine is an indispensable equipment for processing all kinds of wires and cables. It is a high-end technological product with multi-function machine of gathering and feeding material cutting, stripping, pressing together, humanization and intellectualization. It hardly needs manual work in the process of operation, but it also has faults. This paper summarizes the three most common faults in the process of operation of automatic terminal machine.
One. The length of electronic wire cut-off by fully automatic wire crimping machine is different.
1. The feeding wheel pressed too tight or too loose. If the problem is caused by this phenomenon, we can solve this problem only by adjusting the gap between the two wheels with the fine-tuning parts of the rolling wheel so that the wire is not flattened or too loose and slippery.
2. The straightener is too tight or loose. If it is because of this problem, then we should adjust the straightener to play a straightening role and send it out smoothly as the principle to solve it.
3. The cutting edge is worn or the cutting edge is worn. In view of this phenomenon, we only need to replace the new cutting knife.
Two. The machine cannot start or stop in operation
First check whether there is current input (220V) and 6KG air pressure, then check whether the total set number arrives, whether there is wire or a certain part of the machine jammed, finally check whether there is signal connection or power connection of the automatic wire crimping machine and lead to the wire crimping machine without crimping.
Three. Some Copper Wires Outstrench From Crimped... read more
18
Jun
Generally, there are many reasons for overheating of bearings in automatic wire crimping machines. Among them, there are several common reasons. The wire crimping machine manufacturer introduce several reasons as below:
1. Friction between bearing cover and shaft.
Because the axis of the axle and the axis of the mechanical equipment driven by the terminal machine are not on the same line, or because of the inaccurate processing, the inner circle of the bearing cap is eccentric, so that the bearing cap and the axle are friction with each other. Light bearings heat, serious smoke, large high-speed motors will soon rub red. At this time, the machine should be stopped immediately, otherwise the automatic terminal machine will be burnt down.
2. If the belt is too tight or the axle center of the fully automatic wire crimping machine is not in the same straight line as that of the driven machine, that is to say, the bearing load will increase and the bearing will heat up.
3. The unbalance of inner and outer rings of steel ball bearings is one of the causes of heating.
The unbalance of inner and outer rings of terminal machine may be caused by machining. Because the seat and cover of automatic terminal machine are processed separately, sometimes the bearing holes on the two end caps are not coaxial (that is, the center line is not on one line). In addition, poor assembly, uneven tightness of the screw on the end cover, dust and dirt on the stop, etc., may also make the inner and outer rings unbalanced. If the inner and outer rings of the bearing are unbalanced, the steel beads and the inner and outer rings will be scraped, and the friction will increase and heat up. If there is no other reason, wipe the nose clean and reinstall, screw tighten one by one in diagonal order. A small amount of errors in processing can be improved by gradual automatic adjustment.
4. Too much or too little lubricating oil is also the cause of heating.
Bearing is used for a long time, the internal lubricant gradually reduces, resulting in insufficient lubrication, increased friction loss, so that the bearing heating, long-term oil shortage operation will cause bearing damage. Too much oil or too thick oil can also cause bearing overheating. In addition, if the lubricating oil is mixed with hard impurities, the bearings are not cleaned, or the bearings are cleaned with dirty oil, so that there are sand particles and iron chips in the bearings, the mechanical friction of the bearings will be increased and the bearings will be heated, and the bearings will be easily damaged due to the role of impurities.
read more
25
Oct
The situation of Chinese wire harness exports is very good. According to statistics from relevant agencies, domestic wire harness products have earned 3.27 billion US dollars, an increase of 62.7% over the previous year. There are indications that China has become a major exporter... read more
02
May
In order to maximize the function of automatic wire strip and crimp machine in the process of use, it is important to know how to use them. Before using automatic wire strip and crimp mahcine, the following points should be noted:
1. To be set on a smooth and non-vibrating ground or table, there should be enough space for heat dissipation.
2. The basic power supply is 220 V AC. The special power plug provided with the machine should be used.
3. Use special and suitable sockets; make sure the appropriate operating temperature (0-40 degrees Celsius).
4. When you don’t use the machine for a long time, you must unplug the power and cover the machine with dust-proof appliances.
5. Do not set and install in high temperature areas.
6. Undergraduates can not modify machinery and control circuits, which will cause the slider to fall twice and so on.
7. Safety devices or rear panels should not be removed and the installation location should not be changed.
8. Make sure that the anhydrous pipe is connected before use in order to work normally.
9. Burn danger: If touching a motor-like hot product, the operator is in danger of being scalded! Never touch it with your hands during long hours of work!
10. Electrical shock danger: If touching the electrified part has the danger of transmitting electricity, do not touch the motor or plug socket with wet hand. If there is leakage, we must let the professionals change the parts of the machine!
11. Pressure risk: Do not touch the moving parts of the wool rod and cylinder, there is the risk of pinch and crush injury!
However, in the process of use, the following points should be paid special attention to.
1. In the process of operation, if the machine is abnormal, turn off the power supply, and timely invite maintenance personnel to repair and debug.
2. Non-designated personnel shall not debug or disassemble machine parts.
3. In the process of operation, the power supply of the machine has been cut off. It is strictly forbidden for finger or any part of the body to enter the punching range in order to avoid accidents.
4. At work, if you need to leave, turn off the power before leaving.
5. The replacement of terminals must first disconnect the power supply and then replace the operation. The operation of the replacement machine is strictly prohibited.
6. In the process of operation, if the tool die terminal card is used, the scissors or needles must be used to take it out and continue to work.
Correct operation mode of fully automatic wire crimping machine is very important. It can not only ensure human safety, effectively avoid all kinds of potential safety hazards when the machine is in use, but also improve the production efficiency of the machine. This is the best manifestation of grinding the knife without mistake and chopping the firewood. In addition, the correct use of the machine can greatly extend the service life of the machine.
read more
02
May
Fully automatic wire crimping machine has the functions of automatic cutting, stripping, twisting and crimping, which is a highly automated equipment. In the course of using, how to detect and eliminate faults? Fortune Sky Technology teaches you how to detect and eliminate faults: only fully check and clean up the machine and equipment before working every day, most of the faults can be prevented. It is very important to check and clean up before operation. If a fault occurs in one part, it will affect the normal operation of other parts and make the fault more serious. Therefore, it is necessary to repair it in time when abnormal is found. This can reduce the normal production or other unnecessary losses caused by the failure of machinery and equipment.
1. Fault: The cutting length of the electronic wire is inconsistent
Reason a: the wire feeding roller is pressed too tight or loose;
Solution: adjust the gap between the two wheels with the fine-tuning parts of the roller so that the wire is not flattened and too loose to slip.
Reason b: Straightener is too tight or loose;
Solution: The principle of adjusting straightener is that straightener can play a straightening role and be delivered smoothly.
Cause c: abrasion of the cutting edge;
Solution: Replace the new cutting blade.
2. Fault: The length of stripping opening is different.
Reason a: the wire feeding roller is too tight or loose;
Solution: adjust the gap between the two wheels with the fine-tuning parts of the roller so that the wire is not flattened and too loose to slip.
Reason b: Cutter cut too shallow or too deep;
Solution: Debugging the knife edge to the appropriate position with the depth adjusting part of the cutting knife, so as not to hurt the copper wire and to smoothly peel off the insulation.
Reason c: Cutting tool abrasion;
Countermeasure: Replace new blades.
3. Fault: The machine can not start or stop in operation.
Reasons and countermeasures:
A. Check for current input (220V) and 6KG air pressure;
B. Check if the total number of settings has arrived or not, and if it has arrived, reset it and start it after power failure;
C. Check if there is a wireless material or a running part jammed;
D. Check if the wire crimping machine has signal connection or power connection and lead to the wire crimping machine without crimping.
4. Faults: uneven exposure of copper wire on the crimped terminal;
Reasons and countermeasures:
A. Check if the catheter of gun-type swing arm is attached to the wire;
B. Check if the cutter edge of wire crimping machine is relatively straight with the catheter of... read more
25
Jun
(1) Fully automatic wire crimping machine stamping guide rail must be added oil lubrication filling hole at the top of the terminal machine once an hour, each filling 2-3 drops should not be too much.
(2) Operators must clean the machine every day to remove dust and debris on the surface of the machine and excess oil pollution.
(3) Grease must be added to the main speed bearing of the automatic wire crimping machine every week.
The specific operation methods are as follows:
Opening the rear cover of the wire crimping machine
Removing the clip spring of driven pulley,
Removing pulley,
Smearing grease (uniformly applied on the surface of high speed bearing) and restoring (note: in the process of removing pulley, attention to bearing balls perhaps be lost).
After 3-6 months using the fully automatic wire crimping machine, it is necessary to check whether the parts (wearing parts) need to be replaced, such as belt, and whether the spring elasticity of each part needs to be replaced. Whether the locking screw of the machine is loose or not, check whether the clamp spring is deformed, etc.
Usually in the work, we not only need to know how to use the automatic terminal machine, but also need proper maintenance. Without maintenance, not only will reduce the life of the machine terminals, but also the maintenance skills of the automatic terminal machine will affect the efficiency of the machine.
Maintenance process of automatic terminal machine
1. (Stepping Principle) The motor keeps turning. There is an internal wrapped breaker with a clutch. Every step produces a standard “O” coming out, which is the most common.
2. In the last five years, there has been a mute wire crimping machine with a servo. Its operating principle is different from that above. It just gives the servo a message, which is then transmitted to the motor and acts as an action.
As long as the wire is worn, the applicator installed, production can start... read more
25
Oct
In recent years, fully automatic pvc twin wire crimping machine has been warmly welcomed by the majority of manufacturers in wire harness processing industry . It integrates a variety of processing functions. It saves a lot of manpower cost and improves production efficiency. So... read more
12
Jun
All kinds of electrical appliances used in our life include cars and aerospace, wiring harness is the main part of the success of commodities, and different wiring harness will be used in the development of each commodity. As the wiring harness processing equipment, computerized wire... read more
09
Apr
Shenzhen Fortune Sky Technology Co.,Ltd tell you the fully automatic wire terminating machine operating procedures
3.1 Checking fully automatic wire terminating machine before its start :
3.1.1 check whether the switch is good.
3.1.2 check the electrical device is normal (Power: 220V, air pressure: 3.5-6.5 pure)
3.1.3 Lubricate in the sliding part,... read more
07
Mar
I believe everyone knows the function of fully automatic wire crimping machine and wire crimping machine. Among them, this fully automatic wire crimping machine has many advantages compared with the general wire crimping machine.Compared with the full automatic wire crimping machines in the market, the advantages of... read more