Chinese wire terminal crimping machine manufacturer describes how to assembly the automatic wire terminal crimping machine and its main purpose

1. The main working principle of mechanical type is driving machine working by belt and cam. The advantage is cheap, but the disadvantage is that the mechanical parts are easy to wear and aging after using for a period of time, and the maintenance and debugging are troublesome. Short service life. 2. Stepping full automatic wire crimping machine is mainly driven by stepping motor. Its advantage is that the price is relatively low and the appearance is close to the servo motor. Compared with mechanical design, it is more exquisite. The disadvantage is that domestic ordinary stepping motor is easy to lose step and affects the accuracy of products. The service life is short. The price difference between domestic stepper motor and imported famous brand servo motor is about 10 times. At present, more small companies use stepper motors as servo motors, declare that they are all servo products, or use some unknown servo plus some cam mechanical parts to deceive consumers. 3. Full servo mainly controls the movement of servo motor by servo drive signal provided by PLC. Its advantages are high precision, long service life, high cost performance, and its disadvantage is that the price is relatively expensive. The servo motor, together with imported famous brand reducers such as Shimpo in Japan, Sumitomo, HD, Alpha in Germany, is used together with the motion module (well-known ones such as THK, etc.), which greatly ensures the safety of the servo motor. The accuracy and service life of the product are proved. The installation steps of automatic wire crimping machine are as follows: 1. Before installing the applicator, need to check whether the upper and lower die blades and feeding fastening screw are tightened or not. 2. Pull up the slider of the applicator and cover the sliding groove into the 2000 mould handle or (insert the power supply, press the adjustment button, rotate the back spindle counterclockwise with an open-mouth wrench, make the press slide down quickly and cover the sliding groove of the applicator into the 2000 mould handle). 3. Fix the bottom plate of the die and the working table of the press with the fixed screw of the press plate, so that the whole set of die can not be loosened (the whole set of die is in a solid state in normal operation). The wire crimping machine manufacturer introduces the following use steps in details: 4. After the applicator is installed, in the mode of manual operation, the back spindle is rotated counterclockwise with an open mouth wrench to see if the upper and lower die blades are centered and vertical. 5. Adjust the pressure height of upper and lower stroke. 6. After the terminal is loaded into the die feeding plate from the guide plate, please tighten the terminal pressure adjustment screw properly so that the terminal does not retreat in normal operation. 7. In the mode of manual operation, try to crimp terminal, check if the feeding head can normally send the terminal to the center of the upper and lower dies. 8. Try to crimp the terminals after adjustment, start tension test after 10 terminals crimped, if tension test are passed then start production. if there are problems, find out the problems are and correct them.

problems and solutions of several computerized wire stripping machines

A brief introduction to the problems and solutions of several computerized wire stripping machines Computerized wire stripping machine is widely used at the end of the wire processing equipment, to wire and cable factory is essential, the performance of computerized wire stripping is directly related to the production efficiency. Understanding of the production process of the machine, and how to solve the problem is particularly important. The following are the common problems and solutions of the computerized wire stripping machine: 1, computerized wire stripping [...]

Solutions for some problems of computerized wire stripping machine

Solutions for  some problems of computerized wire stripping machine 1, computerized wire stripping machine shows appearance of copper wire intercept or cut off when it’s working? The primary reason is the knife value is too small. Solution: the need to increase the value of the knife, the knife to adjust the value of the planning according to your existing wire to be fixed, can be modified. 2, the machine starts the alarm sound? Please check the parameters can be set correctly, please note that the upper [...]

Do you know advantages of multifunctional high-speed computerized wire stripping machine?

1.) multifunctional high-speed computerized wire stripping machine is a high-speed wire harness automatic cutting off,both-ends stripping, one end strip and partial stripping machine. 2.) the use of servo motor control cutting, peeling and other actions becomes more accurate. 3.) the length of the transformation and full stripping, semi stripping using key settings, simple and fast. 4.) the change of stripping length and incision adopt fine-tuning rotation mode, simple and fast. 5.) computerized wire stripping machine speed can be divided into five sections, according [...]

Solutions For Failure Of Automatic Wire Stripper

1.) run silent appear “Err02”: fuse is broken, replace it and try again, if broken again, need to replace one of the drive board. 2.) run but immediately shut down to display “Err02”: wire section is too thick, too fast, slow adjustment again; insufficient voltage stabilized power supply, with independent; cutter head sensor dust or knife head sensor positioning sheet change position, need to clean up or iron re-positioning. 3.) show “Err01” wire cut several pieces and automatic shutdown: clearance of [...]

Computerized wire stripping machine manufacturers talk about the reasons for the failure of cable performance

Computerized wire stripping machine manufacturers introduce the reasons for the failure of the cable performance is as follows: (1) free discharge and dielectric loss The reasons for the failure of free discharge and dielectric loss are very complicated. Whether the insulation contains bubbles and impurities, and the properties of the raw materials are closely related. The method is to keep the raw material clean, strictly according to the production process. (2) cable insulation breakdown Computerized wire stripping machine manufacturers tell you, cause the [...]

Brief Analysis of Main Components of Wire Stripping Machine

Brief analysis of main components of wire stripping machine for sale 1. wire stripping machine for sale working principle: conveyor wire through wire feeding wheels and wire outlet wheels,complete cutting and stripping through turret assembly.Brief analysis of main components of wire stripping machine Wire stripping machine for sale working principle: conveyor wire through wire feeding wheels and wire outlet wheels,complete cutting and stripping through turret assembly. 1.) Wire feeding wheel lifting up knob: wire stripping machine lift up the knob while wire pass through [...]

Which brand of automatic wire stripping machine?

Are you still hesitated on choice which brand of automatic wire stripping machine?Manufacturer is here! automatic wire stripping machine currently on the market are similar appearance, the appearance is difficult to discern just automatic wire stripping machine quality is good or bad, especially a friend new to computers stripping machine is unable to start , then when we buy automatic wire stripping machine should pay attention to those points out 1.) Stripping Speed:The reason to choose the high-tech factory automation equipment [...]

Incredible!Automatic wire stripping machine makes your hands free.

That’s why more and more manufacturers choose automatic wire stripping machine? Let your hands free! The appears of automatic wire cutter stripper is completely solved heavy work of manually stripping the insulation of wire, simplied a lot of tedious work, effectively improve the work,the emerge of computerized wire cutting stripping machine and automated wire cutter stripper makes the efficiency of the work continuously improve accuracy. we summarize the overall performance advantage of automatic wire cutter stripper with the following points. 1.) [...]

This machine uses a hybrid drive microcomputer control system of the whole LCD screen, cutting,stripping,twisting,middle stripping, one-time completion, but also the front half stripping with twisted wire function, protect the integrity of the wire, special wire can instantly change the size of wire specification.

Main Componets Function On Automatic Wire Stripping Machine

Main Componets Function On Automatic Wire Stripping Machine 1. The principle of work for Automatic Wire Stripping Machine: Transmission wire through inlet wire wheel and outlet wire wheel and complete the cutting and stripping with knife rest assembly. 2. Brief introduction to main components function: (1) Inlet wire wheel uplift knob: uplift inlet wire wheel while Automatic Wire Stripping Machine‘s threading, turn the knob clockwise to raise up inlet wire wheel, so that you can smoothly pass through the wire; In opposite, anticlockwise turn the [...]