This automatic wire terminal crimping machine will have a great impact when it is working,so as to ensure the safety of the staff,it is necessary to master the correct operation method and pay special attention to it in the use process.Compared with general wire terminal crimping machine,the performance of fully automatic wire terminal crimping machine may be more perfect.Although automation can be achieved,some basicoperation methods still need to be mastered. When using automatic wire terminal crimping machine,first turn on the power switch,the indicator light will be [...]
In order to maximize the function of automatic wire strip and crimp machine in the process of use, it is important to know how to use them. Before using automatic wire strip and crimp mahcine, the following points should be noted: 1. To be set on a smooth and non-vibrating ground or table, there should be enough space for heat dissipation. 2. The basic power supply is 220 V AC. The special power plug provided with the machine should be used. 3. Use special and suitable sockets; make sure the appropriate operating temperature (0-40 degrees Celsius). 4. When you don’t use the machine for a long time, you must unplug the power and cover the machine with dust-proof appliances. 5. Do not set and install in high temperature areas. 6. Undergraduates can not modify machinery and control circuits, which will cause the slider to fall twice and so on. 7. Safety devices or rear panels should not be removed and the installation location should not be changed. 8. Make sure that the anhydrous pipe is connected before use in order to work normally. 9. Burn danger: If touching a motor-like hot product, the operator is in danger of being scalded! Never touch it with your hands during long hours of work! 10. Electrical shock danger: If touching the electrified part has the danger of transmitting electricity, do not touch the motor or plug socket with wet hand. If there is leakage, we must let the professionals change the parts of the machine! 11. Pressure risk: Do not touch the moving parts of the wool rod and cylinder, there is the risk of pinch and crush injury! However, in the process of use, the following points should be paid special attention to. 1. In the process of operation, if the machine is abnormal, turn off the power supply, and timely invite maintenance personnel to repair and debug. 2. Non-designated personnel shall not debug or disassemble machine parts. 3. In the process of operation, the power supply of the machine has been cut off. It is strictly forbidden for finger or any part of the body to enter the punching range in order to avoid accidents. 4. At work, if you need to leave, turn off the power before leaving. 5. The replacement of terminals must first disconnect the power supply and then replace the operation. The operation of the replacement machine is strictly prohibited. 6. In the process of operation, if the tool die terminal card is used, the scissors or needles must be used to take it out and continue to work. Correct operation mode of fully automatic wire crimping machine is very important. It can not only ensure human safety, effectively avoid all kinds of potential safety hazards when the machine is in use, but also improve the production efficiency of the machine. This is the best manifestation of grinding the knife without mistake and chopping the firewood. In addition, the correct use of the machine can greatly extend the service life of the machine.
Fully automatic sleeve insertion terminal crimping machine is generally used to play the spring terminal and can automatically wear the jacket. To distinguish the quality of an automatic sleeve insertion terminal crimping machine, we can judge from the following aspects. 1. Whatever the buzzword, the principle is much the same. First of all, depending on the configuration, a fully automatic terminal crimping machine with bad configuration is no better than that. Many times it is broken because of a screw or burr. Therefore, it must not be saved in this respect. The fully automatic sleeve insertion terminal crimping machine must be equipped with high configuration. The motor is the most basic servo, preferably the top Mitsubishi servo. 2. Stripping and cutting effect, we should carefully observe whether the wire stripped by fully automatic sleeve insertion terminal crimping machine will not be clean, stripping is not aligned, whether the copper wire is injured or not, whether the insulation is scratched or not, whether the wire is obvious crooked and different lengths or not, and so on. If the bad stripping will affect the effect of subsequent sleeve insertion and terminal crimping, which is not acceptable. Of course, there is an error in the length of stripping and cutting, which is 0.2 mm + (set length * 0.002 mm). 3. The effect of crimping terminal, the quality of a fully automatic sleeve insertion terminal crimping machine depends mainly on the effect of crimping terminal. If the crimped plug spring terminal is crooked, or does not crimp copper wire, or the crimping interface is loose, it will directly affect the quality of your product. This will be a fatal injury. As mentioned above, using Mitsubishi servo can better avoid this problem. 4. The speed of fully automatic sleeve insertion terminal crimping machine. If the above two points are almost the same, the working speed of fully automatic sleeve insertion terminal crimping machine will be another important indicator. Enterprises choose fully automatic sleeve insertion wire crimping machine mainly focus on its automation, if its speed is higher, it represents that it will bring you greater benefits, of course, the premise is that the wire harness processed by fully automatic sleeve insertion terminal crimping machine is qualified products. 5. Not long after the machine was born, the machine that just came out for a year or two may have many problems, instability, and we can’t pay for their instability. Nowadays, there are many enterprises that produce fully automatic sleeve insertion terminal crimping machine and their appearance is quite similar. And now many enterprises will use automatic terminal crimping machine, so it is particularly important to know how to select terminal crimping machine.
1. The length of the stripping opening of fully automatic ribbon cable terminating machine is different: There are many common reasons for opening disagreement, such as wire is pressed too tight or loose by wire feeding wheels; so you only need to adjust the space between the two wheels with a roller trimmer so that the wire does not flatten or slip too loosely. If the cut is too shallow or too deep, let’s adjust the knife edge to the right position with the knife depth conditioner, so as not to hurt the copper wire and to drop the rubber smoothly. If the opening is still different, replace the new blade directly. 2. Copper wire is exposed and uneven while terminating ribbon cable the copper wire : Check whether the gun-type swing arm catheter can be attached to the wire or not; Check whether the knife edge of wire crimping machine can be straight with the swing arm catheter or not; Check whether the auxiliary pressing block of the wire crimping machine can be loosened or not; Check whether the interval between the terminal machine and the automation has been changed or not. 3. The automatic ribbon cable terminating machine can not start or stop working: Unable to start or suspend work, first of all, we must check whether there is current input and 6KG air pressure, as well as whether there is wire or a part of the machine jammed or not; and check whether the wire crimping machine has signal or power connection which leads to the machine doesn’t crimp. 4. Wire interception of automatic ribbon cable terminal crimping machine leads to different length: Change new blade. Pressure of wire feeding wheels are too tight or loosen, so you only need to adjust the space between the two wheels with a roller trimmer so that the wire does not flatten or slip too loosely. Matters needs attention in maintenance of automatic ribbon cable terminating machine In order to prevent accidents or damage to the machine, the following principles must be observed in overhaul: 1. Only trained professionals are allowed to repair machines or replace components. When a fault occurs, press the jerk button on the operation panel to stop the machine. 2. When the machine fails to work properly, consult relevant manuals and instructions to determine the correct measures to be taken. 3. If two or more people work together, they must establish links with each other so that they can inform each other before starting new work steps to ensure personal safety. 4. Many electrical components are installed on the machine. The installation position of these components is vulnerable to oil pollution, dust and vibration. A large part of the machine failure is caused by these components. Because the operation and maintenance of most components are relatively simple, the fault can be detected and repaired according to the user’s own strength. The terminal manufacturer said it should be noted that only the specified components are allowed to replace the damaged parts. 5. Power must be turned off before repairing or replacing components. 6. Parts (components) removed during overhaul should be replaced in place with the same new parts (components) and fixed with the original specifications screw as far as possible. 7. Instruments used in overhaul must be calibrated. 8. It is strictly forbidden to leave inflammables or metal objects in cabinets or junction boxes. 9. Check the cable and wire regularly to prevent leakage or shock. In-cabinet maintenance: Before opening the cabinet door, the main switch of the cabinet should be disconnected. After the main switch is disconnected, the main switch is still live. Therefore, maintenance personnel must pay special attention to it. If it is necessary to open the cabinet door electrically for repair, attention should be paid to safety, and no touching of charged objects in the cabinet by hand should be strictly prohibited.
Now the industry is developing very fast, and some machines are often renewed. So let’s see how the pipe cutter develops. With the large-scale use of our company’s automatic silicone tube cutter in the market, more and more customers have different needs. At present, our company’s silicone tube cut to length machines have several models in accordance with different types of silicone tubes. The following is an introduction for customers: 1. When choosing cut to length machines (including silicone tube cutters and heat shrinkable tube cutters), customers must choose more professional companies that are well-known in the cutting industry. Fortune Sky has guaranteed after-sales service regardless of product quality (the simplest way to distinguish is whether the company’s website is regular or not, and whether there are many kinds of product cutting equipment, generally speaking, cutting equipment types. Manufacturers with more categories are constantly improving because of more requirements from customers, resulting in more types and more professionals. 2. Choose the price of the automatic silicone tube cutter, of course, you get what you pay for is universal, especially in terms of equipment, after all, it also involves after-sales and maintenance. 3. Customers should choose according to their own needs. For example, if you are in the medical industry, you should choose the silicone tube cutting machine for medical tubes, and the industrial silicone tube cutting machine for industrial silicone tubes. 3. It is very important to use good steel for cutting silicone tube. Generally, the quality of domestic steel is poor, we use imported high-speed steel, durable. Working principle: Its principle is to control the direction of oil path movement of hydraulic system by electrical system through the cooperation of computer and hydraulic system, and to promote the straight-line back and forth movement of the trailer. The micro-computer will walk according to the knife-walking route designed by the user. In the round-trip movement, the signals detected from the limit of the trailer board will be used as the basis to control and change the oil-path movement, so as to achieve the desired knife-walking route.
Dear Valued Customers, Have a nice day. Pls be kindly advised that our chinese will have holidays from April 5th to 7th for Qingming Festival and resume to work on April 8th. Thanks for your choice on our machines and tools. Any urgency pls feel free to contact us on whats app or wechat: 0086-19970532453 or send email to email@example.com, we will take quick responce.
Dear All Valued Customer, Wish you success in your career and happiness of your family! Our company will close to work on Jan 27th and resume to work on Feb 14th for Chinese Lunar New Year 2019, any emergency please feel free to contact us via mobile no./whats app/wechat:0086-19970532453. Thanks.
Failure 1: Stripping front opening length varies. Reason a: Feeding wire wheel is too tight or relaxed; Solution: use wheel trimming bar to adjust two wheels gap so as not to press the wire firmly or too relaxed to slip the wire. Reason b: cutting and stripping knife cut too shallow or too deep; Solution: use knife deep shallow adjust bar to move knife-edge to the appropriate location, in order not to hurt the copper wire and can smooth off the rubber. Reason c: [...]