08
Apr
The clamp of IDC connector crimping machine is adjustable, there are two kinds of specifications, the one with 1.0 maximum spacing can crimp 64P, the one with 1.27 maximum spacing can crimp 50P, 1.0 or 1.27 spacing fixture will be sent with machine at... read more
30
Apr
1. The length of the stripping opening of fully automatic ribbon cable terminating machine is different:
There are many common reasons for opening disagreement, such as wire is pressed too tight or loose by wire feeding wheels; so you only need to adjust the space between the two wheels with a roller trimmer so that the wire does not flatten or slip too loosely. If the cut is too shallow or too deep, let’s adjust the knife edge to the right position with the knife depth conditioner, so as not to hurt the copper wire and to drop the rubber smoothly. If the opening is still different, replace the new blade directly.
2. Copper wire is exposed and uneven while terminating ribbon cable the copper wire :
Check whether the gun-type swing arm catheter can be attached to the wire or not;
Check whether the knife edge of wire crimping machine can be straight with the swing arm catheter or not;
Check whether the auxiliary pressing block of the wire crimping machine can be loosened or not;
Check whether the interval between the terminal machine and the automation has been changed or not.
3. The automatic ribbon cable terminating machine can not start or stop working:
Unable to start or suspend work, first of all, we must check whether there is current input and 6KG air pressure, as well as whether there is wire or a part of the machine jammed or not; and check whether the wire crimping machine has signal or power connection which leads to the machine doesn’t crimp.
4. Wire interception of automatic ribbon cable terminal crimping machine leads to different length:
Change new blade.
Pressure of wire feeding wheels are too tight or loosen, so you only need to adjust the space between the two wheels with a roller trimmer so that the wire does not flatten or slip too loosely.
Matters needs attention in maintenance of automatic ribbon cable terminating machine
In order to prevent accidents or damage to the machine, the following principles must be observed in overhaul:
1. Only trained professionals are allowed to repair machines or replace components. When a fault occurs, press the jerk button on the operation panel to stop the machine.
2. When the machine fails to work properly, consult relevant manuals and instructions to determine the correct measures to be taken.
3. If two or more people work together, they must establish links with each other so that they can inform each other before starting new work steps to ensure personal safety.
4. Many electrical components are installed on the machine. The installation position of these components is vulnerable to oil pollution, dust and vibration.
A large part of the machine failure is caused by these components. Because the operation and maintenance of most components are relatively simple, the fault can be detected and repaired according to the user’s own strength. The terminal manufacturer said it should be noted that only the specified components are allowed to replace the damaged parts.
5. Power must be turned off before repairing or replacing components.
6. Parts (components) removed during overhaul should be replaced in place with the same new parts (components) and fixed with the original specifications screw as far as possible.
7. Instruments used in overhaul must be calibrated.
8. It is strictly forbidden to leave inflammables or metal objects in cabinets or junction boxes.
9. Check the cable and wire regularly to prevent leakage or shock.
In-cabinet maintenance:
Before opening the cabinet door, the main switch of the cabinet should be disconnected.
After the main switch is disconnected, the main switch is still live. Therefore, maintenance personnel must pay special attention to it.
If it is necessary to open the cabinet door electrically for repair, attention should be paid to safety, and no touching of charged objects in the cabinet by hand should be strictly prohibited.
read more
25
Oct
The possible factors of terminal rail feed not working are as follows:
1. Lack of power supply voltage.
2. The connecting wire between the terminal rail feed and the controller is cracked.
3. The fuse of the controller is blown out.
4. The coil is burnt out.
5. The... read more
07
Apr
1.) Insulation Failure
The role of insulator is to maitain contact member arranged in correct position. Insulators must possess excellent electrical properties, Insulator surface or internal moisture contamination of the metal extra material, surface dust, flux, organic material precipitates and harmful gas adsorption membrane fusion... read more
25
Oct
Analysis of poor contact problem of wire terminal crimping machine:
For machines, poor contact has always been one of the main causes of failure, ranging from small size like mobile phones to big one like computers, wire terminal crimping machines, or aviation equipment and etc.... read more
25
Jun
(1) Fully automatic wire crimping machine stamping guide rail must be added oil lubrication filling hole at the top of the terminal machine once an hour, each filling 2-3 drops should not be too much.
(2) Operators must clean the machine every day to remove dust and debris on the surface of the machine and excess oil pollution.
(3) Grease must be added to the main speed bearing of the automatic wire crimping machine every week.
The specific operation methods are as follows:
Opening the rear cover of the wire crimping machine
Removing the clip spring of driven pulley,
Removing pulley,
Smearing grease (uniformly applied on the surface of high speed bearing) and restoring (note: in the process of removing pulley, attention to bearing balls perhaps be lost).
After 3-6 months using the fully automatic wire crimping machine, it is necessary to check whether the parts (wearing parts) need to be replaced, such as belt, and whether the spring elasticity of each part needs to be replaced. Whether the locking screw of the machine is loose or not, check whether the clamp spring is deformed, etc.
Usually in the work, we not only need to know how to use the automatic terminal machine, but also need proper maintenance. Without maintenance, not only will reduce the life of the machine terminals, but also the maintenance skills of the automatic terminal machine will affect the efficiency of the machine.
Maintenance process of automatic terminal machine
1. (Stepping Principle) The motor keeps turning. There is an internal wrapped breaker with a clutch. Every step produces a standard “O” coming out, which is the most common.
2. In the last five years, there has been a mute wire crimping machine with a servo. Its operating principle is different from that above. It just gives the servo a message, which is then transmitted to the motor and acts as an action.
As long as the wire is worn, the applicator installed, production can start... read more
04
Apr
Failure 1: Stripping front opening length varies.
Reason a: Feeding wire wheel is too tight or relaxed;
Solution: use wheel trimming bar to adjust two wheels gap so as not to press the wire firmly or too relaxed to slip the wire.
Reason b: cutting and stripping... read more
12
Jun
1. The main working principle of mechanical type is driving machine working by belt and cam. The advantage is cheap, but the disadvantage is that the mechanical parts are easy to wear and aging after using for a period of time, and the maintenance and debugging are troublesome. Short service life.
2. Stepping full automatic wire crimping machine is mainly driven by stepping motor. Its advantage is that the price is relatively low and the appearance is close to the servo motor. Compared with mechanical design, it is more exquisite. The disadvantage is that domestic ordinary stepping motor is easy to lose step and affects the accuracy of products. The service life is short. The price difference between domestic stepper motor and imported famous brand servo motor is about 10 times. At present, more small companies use stepper motors as servo motors, declare that they are all servo products, or use some unknown servo plus some cam mechanical parts to deceive consumers.
3. Full servo mainly controls the movement of servo motor by servo drive signal provided by PLC. Its advantages are high precision, long service life, high cost performance, and its disadvantage is that the price is relatively expensive. The servo motor, together with imported famous brand reducers such as Shimpo in Japan, Sumitomo, HD, Alpha in Germany, is used together with the motion module (well-known ones such as THK, etc.), which greatly ensures the safety of the servo motor. The accuracy and service life of the product are proved.
The installation steps of automatic wire crimping machine are as follows:
1. Before installing the applicator, need to check whether the upper and lower die blades and feeding fastening screw are tightened or not.
2. Pull up the slider of the applicator and cover the sliding groove into the 2000 mould handle or (insert the power supply, press the adjustment button, rotate the back spindle counterclockwise with an open-mouth wrench, make the press slide down quickly and cover the sliding groove of the applicator into the 2000 mould handle).
3. Fix the bottom plate of the die and the working table of the press with the fixed screw of the press plate, so that the whole set of die can not be loosened (the whole set of die is in a solid state in normal operation).
The wire crimping machine manufacturer introduces the following use steps in details:
4. After the applicator is installed, in the mode of manual... read more
04
Jul
Benchtop wire terminator crimping machine is developed with modern frequency converter control technology, which is aimed at common terminal applicator crimping at home and abroad. It is suitable for crimping various terminals and wires. Digital control, safety protection system and simple operation realize the... read more
07
Mar
What are the main factors affecting the quality of fully automatic wire crimping machine?
Every kind of mechanical equipment has a quality assessment method.To evaluate its quality, the most common is whether the performance is stable, whether there are faults in the use process, whether the... read more
