How to distinguish an automatic wire stripper and crimping machine, we can judge it from the following aspects:
1. All changes do not depart from their ancestors. First of all, look at the configuration. If a machine with poor configuration, the performance will be no... read more
In order to ensure the safety of the staff, it is necessary to master the correct operation method and pay special attention to it in the use process. Compared with general wire crimping machine, the performance of fully automatic wire crimping machine may be... read more
Shenzhen Fortune Sky Technology Co.,Ltd tell you the fully automatic wire terminating machine operating procedures
3.1 Checking fully automatic wire terminating machine before its start :
3.1.1 check whether the switch is good.
3.1.2 check the electrical device is normal (Power: 220V, air pressure: 3.5-6.5 pure)
3.1.3 Lubricate in the sliding part,... read more
Mechanical failure is a common, automatic terminal crimping machine is no exception, there are many kinds of failures of automatic terminal crimping machine, today is mainly with you about what’s reason caused automatic terminal crimping machine bad contact.
Full automatic terminal crimping machine is necessary to have a good touch... read more
Fully automatic wire crimping machine combines the structural advantages of single-end high-speed automatic wire crimping machine. Double-end single-end crimping terminal, super high speed, single-end crimping can reach 7000 or so pcs per hour, the total length of ultra-short wire incl. cutting and crimping terminal is 9MM. Double-ends crimping 5000pcs or so per hour, ultra-short wire cutting wire and crimping is 40MM or so. The automatic double-ends wire crimping machine mainly adopts imported original parts to complete stripping, cut to length, terminal crimping, half-stripping, twisting and other precise movements, simple operation and stable performance. Suitable for cutting AWG#30-AWG#18 wire.
Simple disposal of sudden abnormality by fully automatic wire crimping machine
As an advanced intelligent equipment, fully automatic wire crimping machine is widely used in wire harness processing industry. Fully automatic wire crimping machine not only has high processing speed, but also has high processing accuracy. It is an indispensable mechanical equipment in wire harness processing industry. Advanced equipment also marks the development of enterprises. Wire harness industry uses intelligent automatic... read more
The possible factors of terminal rail feed not working are as follows:
1. Lack of power supply voltage.
2. The connecting wire between the terminal rail feed and the controller is cracked.
3. The fuse of the controller is blown out.
4. The coil is burnt out.
5. The... read more
1, failure: the length of the different stripping opening;
Reason a: the wire inlet wheel pressed too tight or loose;
Countermeasures: use wire roller fine-tune piece to adjust the gap of wire inlet wheels until the wire won’t be compressed flattened or too loosen slip.
Reason B:... read more
Wire crimping machine refers to a kind of machine used in wire processing. It can crimp metal terminal to the wire end and then make conduction. The terminals crimped by the wire terminator crimping machine are usually for the convenience of connection. Without welding, the two wires can be connected together steadily, and only need to be pulled out when disassembling.
1. The motor keeps turning. There is an internal wrapped breaker with a clutch, every move generates a standard “O” out, which is the most common.
2. In the last five years, mute wire crimping machine with servo have appeared. Their operating principles are different from those above. They just give the servo a message, which is then transmitted to the motor and acts as an action.
3. Terminal crimping and excellent quality products.
Automatic wire crimping machine is an indispensable equipment for processing all kinds of wires and cables. It is a high-end technological product with multi-function machine of gathering and feeding material cutting, stripping, pressing together, humanization and intellectualization. It hardly needs manual work in the process of operation, but it also has faults. This paper summarizes the three most common faults in the process of operation of automatic terminal machine.
One. The length of electronic wire cut-off by fully automatic wire crimping machine is different.
1. The feeding wheel pressed too tight or too loose. If the problem is caused by this phenomenon, we can solve this problem only by adjusting the gap between the two wheels with the fine-tuning parts of the rolling wheel so that the wire is not flattened or too loose and slippery.
2. The straightener is too tight or loose. If it is because of this problem, then we should adjust the straightener to play a straightening role and send it out smoothly as the principle to solve it.
3. The cutting edge is worn or the cutting edge is worn. In view of this phenomenon, we only need to replace the new cutting knife.
Two. The machine cannot start or stop in operation
First check whether there is current input (220V) and 6KG air pressure, then check whether the total set number arrives, whether there is wire or a certain part of the machine jammed, finally check whether there is signal connection or power connection of the automatic wire crimping machine and lead to the wire crimping machine without crimping.
Three. Some Copper Wires Outstrench From Crimped... read more
All kinds of electrical appliances used in our life include cars and aerospace, wiring harness is the main part of the success of commodities, and different wiring harness will be used in the development of each commodity. As the wiring harness processing equipment, computerized wire... read more
1. Turn on the power switch of the automatic cutter stripper wire crimpers, and the power indicator is on.
2. Pay attention to whether there is obvious abnormal noise inside and outside the machine. If yes, immediately stop working, ask the maintenance personnel to determine... read more