Reasons for the wear of the cutting knife of the ultrasonic label cutting machine with sensor

The products cut by the ultrasonic label cutting machine with sensor are beautiful and elegant, without fading, cracking, blackening, and yellowing. The grade of the product has been improved a lot, and the profit is better. But why is its cutter so easy to wear? To understand the cause of cutter wear, you must first understand its working principle: Ultrasonic label cutting machine with sensor is a combination of ultrasonic welding technology and traditional shearing equipment. Its working principle is: when [...]

The reason for the deformation of the roll to sheet cutting machine during rolling and cutting

For the design of the roll to sheet cutting machine, a variety of factors are considered, such as relevant process parameters, tool shape, parameters, rolling and cutting temperature and lubrication conditions, etc. It is proved through practice that the process requirements of the roll to sheet cutting machine are fully satisfied. So why does the roll to sheet cutting machine deform during rolling and cutting? Let me introduce it to you. When the roll to sheet cutting machine rolls in, [...]

Functional characteristics and applicable industries of belt loop cutter

1. Functional characteristics: 1. High speed: 100-120 pcs can be cut per minute. (Take 50mm length as an example) 2. High precision: each cut is monitored by a stepping motor to ensure the high precision of each operation. 3. Smooth cut surface: The hot knife can heat seal the cut surface of colored ribbons and thin textile tapes at high temperature, and the sealing is smooth and free of burrs. 4. The blade is made of imported high-quality steel and has a long [...]

Most complete automatic belt loop cutter common failure problems and several corresponding solutions

1. No power supply? 1. Check whether the power connection plug is in good contact? Check whether the fuse is broken? 2. There is power supply, but it cannot be started, the sensor is wrong, the cutter seat sliding sleeve is stuck or there is no air pressure? 1. Check if the cylinder is ventilated, if not, open the valve. Check whether the cutter seat sliding sleeve is stuck, and fill the sliding sleeve with lubricating oil. 3. No material alarm? 1. Whether the [...]

Roll to sheet cutting machine can automatically cut various strips

Automatic roll to sheet cutting machine can automatically cut various feeding pulleys 1. It can automatically cut all kinds of sheet and tube materials, there is a feeding belt wheel installed at the back of the machine, which can be automatically suitable for the disc placement and feeding of strip coils. 2. The high-speed stepping motor accurately controls the cutting length, the length and speed are adjustable. 3. Roll to sheet cutting machine: cutting time protection, total number setting, batch setting, batch [...]

What are the installation and debugging steps of the computer tape cutting machine after it is delivered to the factory

We tell you what are the installation and debugging steps of the computer tape cutting machine after it is delivered to the factory. Customers need to install and debug after receiving the computer tape cutting machine before it can be applied. What are the installation and debugging steps of the computer tape cutting machine? 1. Make preparations first, prepare the site, power supply, etc.; 2. Inventory of the received EPE vertical cutting machine accessories; 3. Frame rail; 4. The four feet of the guide [...]

Common faults and solutions of belt loop cutter

Next, we will continue to share with you the troubleshooting methods that often occur in the daily practical use of automatic belt loop cutter, and how to deal with a series of fault problems. 1. When using hot cutting, the tape cannot be cut (1) Check whether the temperature reaches the preset temperature. (2) Check whether the hot knife is heated. 2. No power supply (1) Check whether the power connection plug is in good contact. (2) Check whether the fuse is disconnected. 3. There is [...]

Common faults and solutions of belt loop cutter

Next, we will continue to share with you the troubleshooting methods that often occur in the daily practical use of automatic belt loop cutter, and how to deal with a series of fault problems. 1. When using hot cutting, the tape cannot be cut (1) Check whether the temperature reaches the preset temperature. (2) Check whether the hot knife is heated. 2. No power supply (1) Check whether the power connection plug is in good contact. (2) Check whether the fuse is disconnected. 3. There is [...]

Common faults of roll to sheet cutting machine

Next, we will share with you the maintenance methods that often occur in the daily practical use of the roll to sheet cutting machine. 1. The machine keeps cutting, how to deal with no feeding? (1) Whether the materials are used up, please replace with new materials (2) Check whether the material is loaded or the pressure plate falls into the groove (3) If everything is normal, check whether the travel switch is stuck and does not bounce back 2. The length of the [...]

Solution of no display of automatic strip cutter

We tell you the solution for no display on the control panel: If the machine is used continuously for a long time, the temperature inside the case may be extremely high, and the display may be abnormal. This is a normal phenomenon. Stop working, turn off the power switch, and turn it on after a while. The display should be normal. If it is in cold state If the boot display is abnormal, please turn off the power and wait [...]

Online Service
Live Chat