How to operate benchtop wire terminator crimping machine?

Benchtop wire terminator crimping machine is developed with modern frequency converter control technology, which is aimed at common terminal applicator crimping at home and abroad. It is suitable for crimping various terminals and wires. Digital control, safety protection system and simple operation realize the accuracy, strength and safety that the machine can not reach. It makes the terminal machine operate supermutely, and the frequency converter itself can save 30% of electricity, plus the super mute wire crimping machine is working one time and energize one time, to avoid unnecessary idling of the motor, and to save more power when used. Without noise, workers are more attentive to their work, which greatly improves their work efficiency. This is the preferred equipment for wire end processing. Benchtop wire terminator crimping machine is a kind of high-speed automatic wire harness pressing terminal device, the fuselage structure is lightweight, compared with other terminals, the operation sound is smaller, more power-saving. It is very suitable for many domestic high-yield manufacturers to purchase and use. The machine has stable quality, beautiful appearance, elegance and easy operation. This selling wire crimping machine in the terminal market is in great demand and very useful. 1. Confirm the wire nail instructions and the terminal/die to confirm whether it meets the requirements. 2. Start the super mute wire crimping machine and stop the machine according to its operation condition, blade matching, fix the mould and adjust the blade. 3. Install the toolbox with the super- mute wire crimping machine and clamp it with fixture. At this time, use manual tool adjustment to move the slider of the super-silent terminal machine to the bottom dead point, tighten the screw of the tool, adjust the appropriate position of the tool, and then tighten it. At this time, pay attention to the pressure of pressing, and pay attention to the combination of the upper tool and the lower tool, so as to avoid the deviation of the tool from left to right. 4. Try to crimp terminals and wires, according to their crimping conditions, and then make tension test. If it fails to meet the technical requirements, adjust the pressure screw on the super mute wire crimping machine to meet the requirements and lock it. 5. Manual pressure test is used to avoid collision of knives when crimping. Electric operation is used to check whether there is unusual noise or impact sound in the wire crimping machine and applicator, and to check the feeding device and its stroke of the knife blade. 6. After no abnormal idling, 2-3pcs can be produced only after crimping the first inspection and pulling force test. 7. Holding wire and feeding wire in the left hand, feeding and positioning with the right hand, placing the wire mouth on the lower blade and close to the top of the terminal, and stepping on the foot switch on the right foot to separate the clutch mouth, after the clutch mouth is separated, the super mute wire crimping machine drives the applicator and blade to press down the connection and terminal, thus completing the action; 8. Press the “Spare” button on the terminal panel for 4-8 seconds and the program number D001 appears. Press the combination of “Zero” (up) and “Auto/Manu” (shift) to set the program number to D112, press “Spare” (confirm), display “1” (number of connecting terminals), press “Zero” (up) or “Star” (down) to the number of terminals to be hit, and then press “Spare”. Mute wire crimping machine refers to a kind of machine used in wire processing. It can press the hardware head to the wire end. Then do conduction, mute wire crimping machine typed out of the terminal is usually to connect more convenient, without welding can be stable to connect the two wires together, and when disassembly only need to pull it out.

Three most common solutions for wire terminal crimping machines

Wire crimping machine refers to a kind of machine used in wire processing. It can crimp metal terminal to the wire end and then make conduction. The terminals crimped by the wire terminator crimping machine are usually for the convenience of connection. Without welding, the two wires can be connected together steadily, and only need to be pulled out when disassembling. 1. The motor keeps turning. There is an internal wrapped breaker with a clutch, every move generates a standard “O” out, which is the most common. 2. In the last five years, mute wire crimping machine with servo have appeared. Their operating principles are different from those above. They just give the servo a message, which is then transmitted to the motor and acts as an action. 3. Terminal crimping and excellent quality products. Automatic wire crimping machine is an indispensable equipment for processing all kinds of wires and cables. It is a high-end technological product with multi-function machine of gathering and feeding material cutting, stripping, pressing together, humanization and intellectualization. It hardly needs manual work in the process of operation, but it also has faults. This paper summarizes the three most common faults in the process of operation of automatic terminal machine. One. The length of electronic wire cut-off by fully automatic wire crimping machine is different. 1. The feeding wheel pressed too tight or too loose. If the problem is caused by this phenomenon, we can solve this problem only by adjusting the gap between the two wheels with the fine-tuning parts of the rolling wheel so that the wire is not flattened or too loose and slippery. 2. The straightener is too tight or loose. If it is because of this problem, then we should adjust the straightener to play a straightening role and send it out smoothly as the principle to solve it. 3. The cutting edge is worn or the cutting edge is worn. In view of this phenomenon, we only need to replace the new cutting knife. Two. The machine cannot start or stop in operation First check whether there is current input (220V) and 6KG air pressure, then check whether the total set number arrives, whether there is wire  or a certain part of the machine jammed, finally check whether there is signal connection or power connection of the automatic wire crimping machine and lead to the wire crimping machine without crimping. Three. Some Copper Wires Outstrench From Crimped Terminal And Be Uneven. 1. Check whether the gun-type swing arm catheter is attached to the wire rod. 2. Check whether the knife edge of the wire crimping machine is relatively straight with the swing arm catheter. 3. Check whether the auxiliary block of wire crimping machine is loose or not. 4. Check whether the distance between the wire crimping machine and the automatic machine has changed.

Automatic wire terminal crimping machine common troubleshooting method

Automatic wire terminal crimping machine is an indispensable equipment for processing all kinds of wires and cables. It is a high-end technical product of multi-function machine for cutting aggregates and feeding materials, stripping, crimping together, humanization and intellectualization. There is hardly any manual work in the operation process, but there will also be faults. We summarizes the three most common faults in the operation process of automatic wire terminal crimping machine for you: The length of stripping opening is different: There are many common [...]

Daily precautions of automatic wire terminal crimping machine

This automatic wire terminal crimping machine will have a great impact when it is working,so as to ensure the safety of the staff,it is necessary to master the correct operation method and pay special attention to it in the use process.Compared with general wire terminal crimping machine,the performance of fully automatic wire terminal crimping machine may be more perfect.Although automation can be achieved,some basicoperation methods still need to be mastered. When using automatic wire terminal crimping machine,first turn on the [...]

Removal failure of automatic wire terminal crimping machine

Automatic wire terminal crimping machine is an indispensable equipment for processing all kinds of wires and cables.It is a high-end technical product of multi-function machine for cutting aggregates and feeding materials,stripping,pressing together,humanization and intellectualization. There is hardly any manual work in the operation process,but there will also be faults.We summarizes the three most common faults in the operation process of automatic wire terminal crimping machine for you: 1.The length of stripping opening is different: There are many common reasons for different [...]

What are the main factors affecting the quality of fully automatic wire crimping machine?

  What are the main factors affecting the quality of fully automatic wire crimping machine? Every kind of mechanical equipment has a quality assessment method.To evaluate its quality, the most common is whether the performance is stable, whether there are faults in the use process, whether the operation is safe, and so on. Fortune Sky automatic wire cutter stripper terminator is also a kind of mechanical equipment, and it is automatic. Its quality is related to the efficiency and effect of [...]

Fully Automatic Gold Plated Contact Wire Lug Crimping Machine

How to solve bad contact of automatic terminal crimping machine?

How to solve bad contact of automatic terminal crimping machine? Mechanical failure is a common, automatic terminal crimping machine is no exception, there are many kinds of failures of automatic terminal crimping machine, today is mainly with you about what’s reason caused automatic terminal crimping machine bad contact. Full automatic terminal crimping machine is necessary to have a good touch of the layout, reliable and reliable touch stick and excellent conductive function, so the situation is likely to cause the lug [...]