17 Mar

What shall we do if the automated strip cutter cutting is not standard

The first factor may be that the automated strip cutter itself is not good, and the product produced by the machine has a large error. The second factor may be that the pressure on both sides of the roller is not well adjusted, causing uneven pressure on both sides. The third possibility is that the cutter die and other accessories of the automated strip cutter have not been installed and fixed. It is recommended to ask where you bought the machine. [...]

By Hot Cold Strip Cutting Machine , , , , , , , , Read more...
17 Mar

Cut Stop? Problems of Strip Cutting Machine

What is the problem with the automated strip cutting machine faulty knife that cutting cannot stop? How to solve it 1. Check whether the circuit connecting the motor is short-circuited. 2. There is a problem after startup. Check whether the sensor at the connecting rod is normal. 3. Check whether the solid state relay or capacitor is damaged. 4. Check whether the touch screen setting quantity, batch and other data are correct or whether the key setting data is correct. 5. Don’t worry about [...]

By Hot Cold Strip Cutting Machine , , , , , , Read more...
17 Mar

Installation steps of hot cold strip cutting machine

We tell you what are the installation and debugging steps of the hot cold strip cutting machine after it is delivered to the factory. Customers need to install and debug after receiving the hot cold strip cutting machine before it can be applied. What are the installation and debugging steps of the hot cold strip cutting machine? 1. Make preparations first, prepare the site, power supply, etc. 2. Inventory of the received EPE vertical cutting machine accessories. 3. Frame rail. 4. The four feet [...]

By Hot Cold Strip Cutting Machine , , , , , , , , Read more...
17 Mar

Features of automatic cold and hot strip cutting machine

The computer automatic cold and hot strip cutting machine has the following characteristics: 1. The machine tool is made of imported high-quality steel after special treatment. The cut surface is flat during hot cutting, and the hot knife can heat seal the cut surface of various chemical fiber webbing at high temperature, and the seal is flat and free of burrs. There is no need to heat the edge-sealing material, and it can be cut directly without heating. The cold [...]

By Hot Cold Strip Cutting Machine , , , , , , , , Read more...
10 Mar

Common faults and solutions of automated velcro tape cutter

Next, we will continue to share with you the troubleshooting methods that often occur in the daily practical use of the automated velcro tape cutter, and how to deal with a series of fault problems of the automated velcro tape cutter. 1. When using heat cutting, the tape cannot be cut (1) Check whether the temperature reaches the preset temperature. (2) Check whether the hot knife is heated. 2. No power supply (1) Check whether the power connection plug is in good contact; (2) Check [...]

By Hot Cold Strip Cutting Machine , , , , , , , , Read more...
10 Mar

Common faults of automated velcro tape cutter

Next, we will share with you the maintenance methods that often occur in the daily practical use of this automated velcro tape cutter. 1. The cutter keeps cutting, how to deal with no feeding? (1) Whether the materials are used up, please replace with new materials. (2) Check whether the material is loaded or the pressure plate falls into the groove. (3) If everything is normal, check whether the travel switch is stuck and does not bounce back. 2. The length of the cut [...]

By Hot Cold Strip Cutting Machine , , , , , , , Read more...
10 Mar

Velcro tape auto cutter does not cut the tape

1.The bearing of knife is broken in the automatic strip cutter. Check the reason, replace the bearing. 2. Wear of the middle knife. The middle knife has cutting edges on both sides, one side can be worn and the other side can be used or replaced with a new knife. 3. The tube pin of the middle knife is broken. Use a small punch to punch out the broken pin and install a new pipe pin. 4. The tightening force is adjusted [...]

By Hot Cold Strip Cutting Machine , , , , , Read more...
09 Mar

Knife holder structure of automatic hot & cold strip cutter

This automatic hot & cold strip cutter is mainly composed of four parts: microcomputer control, automatic feeding mechanism, belt feeding mechanism and cutting mechanism. The microcomputer control is used to collect set values and send control signals from control center. Automatic feeding mechanism is used for automatic feeding, it is composed of a fixed bracket, an AC motor and a controller. The fixed bracket is used to fix the disk-shaped material and is driven by an AC motor. The [...]

By Hot Cold Strip Cutting Machine , , , , Read more...
Online Service
Live Chat