27 Mar

How to Evaluate the Quality of Automatic Multi Twist Tin 10-Wire Cutting Stripping Machine?

How to Evaluate the Quality of Automatic Multi Twist Tin 10-Wire Cutting Stripping Machine? Typically, the assessment of a mechanical product’s quality is often done through trial and error under normal circumstances, which is a straightforward method. But what if trial is not an option? In such cases, how do we judge? Manufacturer recommendations primarily revolve around three aspects: quality, after-sales service, and pricing. Quality, being of significant influence, is affected by numerous factors during the mechanical manufacturing process, some [...]

By Wire Tin Dipping Machine , , Read more...
22 Mar

Automatic Multi Twist Tin 10-Wire Cutting Stripping Machine: Analysis and Solutions for Abnormal Drop in Solder Pot Temperature

Automatic Multi Twist Tin 10-Wire Cutting Stripping Machine: Analysis and Solutions for Abnormal Drop in Solder Pot Temperature I. Inadequate Preheating of Solder Pot The Automatic Multi Twist Tin 10-Wire Cutting Stripping Machine requires a high-temperature environment for normal operation, and adequate preheating of the solder pot is essential for its proper functioning. If the solder pot is not sufficiently preheated, its temperature will drop automatically during operation. Therefore, if you observe an abnormal drop in the solder pot temperature while [...]

By Wire Tin Dipping Machine , , Read more...
18 Mar

Phenomena and Solutions in the Stripping Process of Automatic Wire Cutter Stripper Machine

Phenomena and Solutions in the Stripping Process of Automatic Wire Cutter Stripper Machine I. Unable to Strip Wire Ends Check the cutting depth of the wire cutter stripper machine. If the cut is too shallow, adjust the wire diameter parameter accordingly. The pressure of the feeding wheel is insufficient. Adjust the air pressure. There may be dirt on the feeding wheel. Clean it thoroughly. The retraction parameters may be set too large or too small. Check if the air supply is normal. II. Unable to Strip [...]

By Fully Automatic Wire Stripping Machine , , Read more...
17 Mar

Automatic Wire Stripping and Bending Machine Clamp Not Gripping Wire: Troubleshooting

Automatic Wire Stripping and Bending Machine Clamp Not Gripping Wire: Troubleshooting I. Causes of the Problem The issue of the clamp not gripping wire in the Automatic Wire Stripping and Bending Machine may arise due to the following reasons: The clamp opening is too large, unable to grip the wire. Severe surface wear of the clamp, unable to grip the wire effectively. Serious internal parts wear of the clamp, resulting in loss of clamping force. Malfunction in the equipment control system, causing the clamp to [...]

By Fully Automatic Wire Stripping Machine , , Read more...
16 Mar

What to Do When the Computerized Fully Automatic Wire Cutter & Stripper Machine Can’t Strip the Wire Ends

What to Do When the Computerized Fully Automatic Wire Cutter & Stripper Machine Can’t Strip the Wire Ends When the Computerized Fully Automatic Wire Cutter & Stripper Machine fails to strip the wire ends, the following measures can be taken to solve the problem: Check the cutting blades of the stripping machine. If the blades are worn or damaged, it may cause the wire ends to be clamped or cut, so it is necessary to check the condition of the blades [...]

By Fully Automatic Wire Stripping Machine , , Read more...
14 Mar

Automatic wire cutting and stripping machine with shortest insulation length for AWG16 to AWG32 wires with shortest insulation length for AWG16 to AWG32 wires

Automatic wire cutting and stripping machine with shortest insulation length for AWG16 to AWG32 wires The parameter settings of the fully automatic computerized wire stripping machine are essential knowledge for personnel in every enterprise to master. These settings mainly include: speed, output, wire twisting, and more. Failing to grasp the method of parameter setting well will hinder the machine from performing its functions effectively. Today, Xiongsheng Electronic Equipment shares a comprehensive guide on the parameter settings of the fully automatic [...]

By Fully Automatic Wire Stripping Machine , , Read more...
13 Mar

How to set up semi-stripping on an automatic wire cutting and stripping machine?

How to set up semi-stripping on an automatic wire cutting and stripping machine? The method for setting up semi-stripping on an automatic wire cutting and stripping machine may vary depending on the model and brand of the equipment, but the general steps are as follows: Turn on the power of the equipment and wait for it to start up. Press the “Settings” or “Parameters” button to enter the equipment settings interface. In the settings interface, find the relevant options such as “Stripping Length” [...]

By Fully Automatic Wire Stripping Machine , , Read more...
11 Mar

How to Set and Adjust Wire Stripping on an Automatic Dual Wire Stripping Machine

How to Set and Adjust Wire Stripping on an Automatic Dual Wire Stripping Machine The setting and adjustment of wire stripping on an automatic dual wire stripping machine are typically done through the control panel. Here are the general steps involved: 1. Access the Wire Stripping Settings: Turn on the control panel. Locate the option for wire stripping settings. 2. Choose Wire Stripping Parameters: Select the desired parameters based on your needs, such as wire gauge, wire length, and stripping depth. 3. Set Wire Stripping Quantity [...]

By Fully Automatic Wire Stripping Machine , , Read more...
Online Service
Live Chat