Single Wire Automatic Terminal Cutting Stripping Crimping Machine

Chinese wire terminal crimping machine manufacturer describes how to assembly the automatic wire terminal crimping machine and its main purpose

1. The main working principle of mechanical type is driving machine working by belt and cam. The advantage is cheap, but the disadvantage is that the mechanical parts are easy to wear and aging after using for a period of time, and the maintenance and debugging are troublesome. Short service life. 2. Stepping full automatic wire crimping machine is mainly driven by stepping motor. Its advantage is that the price is relatively low and the appearance is close to the servo motor. Compared with mechanical design, it is more exquisite. The disadvantage is that domestic ordinary stepping motor is easy to lose step and affects the accuracy of products. The service life is short. The price difference between domestic stepper motor and imported famous brand servo motor is about 10 times. At present, more small companies use stepper motors as servo motors, declare that they are all servo products, or use some unknown servo plus some cam mechanical parts to deceive consumers. 3. Full servo mainly controls the movement of servo motor by servo drive signal provided by PLC. Its advantages are high precision, long service life, high cost performance, and its disadvantage is that the price is relatively expensive. The servo motor, together with imported famous brand reducers such as Shimpo in Japan, Sumitomo, HD, Alpha in Germany, is used together with the motion module (well-known ones such as THK, etc.), which greatly ensures the safety of the servo motor. The accuracy and service life of the product are proved. The installation steps of automatic wire crimping machine are as follows: 1. Before installing the applicator, need to check whether the upper and lower die blades and feeding fastening screw are tightened or not. 2. Pull up the slider of the applicator and cover the sliding groove into the 2000 mould handle or (insert the power supply, press the adjustment button, rotate the back spindle counterclockwise with an open-mouth wrench, make the press slide down quickly and cover the sliding groove of the applicator into the 2000 mould handle). 3. Fix the bottom plate of the die and the working table of the press with the fixed screw of the press plate, so that the whole set of die can not be loosened (the whole set of die is in a solid state in normal operation). The wire crimping machine manufacturer introduces the following use steps in details: 4. After the applicator is installed, in the mode of manual operation, the back spindle is rotated counterclockwise with an open mouth wrench to see if the upper and lower die blades are centered and vertical. 5. Adjust the pressure height of upper and lower stroke. 6. After the terminal is loaded into the die feeding plate from the guide plate, please tighten the terminal pressure adjustment screw properly so that the terminal does not retreat in normal operation. 7. In the mode of manual operation, try to crimp terminal, check if the feeding head can normally send the terminal to the center of the upper and lower dies. 8. Try to crimp the terminals after adjustment, start tension test after 10 terminals crimped, if tension test are passed then start production. if there are problems, find out the problems are and correct them.

Secrets and precautions in using automatic wire strip and crimp machine

In order to maximize the function of automatic wire strip and crimp machine in the process of use, it is important to know how to use them. Before using automatic wire strip and crimp mahcine, the following points should be noted: 1. To be set on a smooth and non-vibrating ground or table, there should be enough space for heat dissipation. 2. The basic power supply is 220 V AC. The special power plug provided with the machine should be used. 3. Use special and suitable sockets; make sure the appropriate operating temperature (0-40 degrees Celsius). 4. When you don’t use the machine for a long time, you must unplug the power and cover the machine with dust-proof appliances. 5. Do not set and install in high temperature areas. 6. Undergraduates can not modify machinery and control circuits, which will cause the slider to fall twice and so on. 7. Safety devices or rear panels should not be removed and the installation location should not be changed. 8. Make sure that the anhydrous pipe is connected before use in order to work normally. 9. Burn danger: If touching a motor-like hot product, the operator is in danger of being scalded! Never touch it with your hands during long hours of work! 10. Electrical shock danger: If touching the electrified part has the danger of transmitting electricity, do not touch the motor or plug socket with wet hand. If there is leakage, we must let the professionals change the parts of the machine! 11. Pressure risk: Do not touch the moving parts of the wool rod and cylinder, there is the risk of pinch and crush injury! However, in the process of use, the following points should be paid special attention to. 1. In the process of operation, if the machine is abnormal, turn off the power supply, and timely invite maintenance personnel to repair and debug. 2. Non-designated personnel shall not debug or disassemble machine parts. 3. In the process of operation, the power supply of the machine has been cut off. It is strictly forbidden for finger or any part of the body to enter the punching range in order to avoid accidents. 4. At work, if you need to leave, turn off the power before leaving. 5. The replacement of terminals must first disconnect the power supply and then replace the operation. The operation of the replacement machine is strictly prohibited. 6. In the process of operation, if the tool die terminal card is used, the scissors or needles must be used to take it out and continue to work. Correct operation mode of fully automatic wire crimping machine is very important. It can not only ensure human safety, effectively avoid all kinds of potential safety hazards when the machine is in use, but also improve the production efficiency of the machine. This is the best manifestation of grinding the knife without mistake and chopping the firewood. In addition, the correct use of the machine can greatly extend the service life of the machine.