25
Jun
(1) Fully automatic wire crimping machine stamping guide rail must be added oil lubrication filling hole at the top of the terminal machine once an hour, each filling 2-3 drops should not be too much.
(2) Operators must clean the machine every day to remove dust and debris on the surface of the machine and excess oil pollution.
(3) Grease must be added to the main speed bearing of the automatic wire crimping machine every week.
The specific operation methods are as follows:
Opening the rear cover of the wire crimping machine
Removing the clip spring of driven pulley,
Removing pulley,
Smearing grease (uniformly applied on the surface of high speed bearing) and restoring (note: in the process of removing pulley, attention to bearing balls perhaps be lost).
After 3-6 months using the fully automatic wire crimping machine, it is necessary to check whether the parts (wearing parts) need to be replaced, such as belt, and whether the spring elasticity of each part needs to be replaced. Whether the locking screw of the machine is loose or not, check whether the clamp spring is deformed, etc.
Usually in the work, we not only need to know how to use the automatic terminal machine, but also need proper maintenance. Without maintenance, not only will reduce the life of the machine terminals, but also the maintenance skills of the automatic terminal machine will affect the efficiency of the machine.
Maintenance process of automatic terminal machine
1. (Stepping Principle) The motor keeps turning. There is an internal wrapped breaker with a clutch. Every step produces a standard “O” coming out, which is the most common.
2. In the last five years, there has been a mute wire crimping machine with a servo. Its operating principle is different from that above. It just gives the servo a message, which is then transmitted to the motor and acts as an action.
As long as the wire is worn, the applicator installed, production can start... read more
07
Mar
Fully automatic wire cutting stripping tinning machine must be operated by trained personnel. Operators should be familiar with the general performance and structure of the machine, master the prevention of equipment failure, judgment and emergency treatment measures. Now we will talk about the considerations of automatic wire... read more
09
Apr
Shenzhen Fortune Sky Technology Co.,Ltd tell you the fully automatic wire terminating machine operating procedures
3.1 Checking fully automatic wire terminating machine before its start :
3.1.1 check whether the switch is good.
3.1.2 check the electrical device is normal (Power: 220V, air pressure: 3.5-6.5 pure)
3.1.3 Lubricate in the sliding part,... read more
25
Oct
The purchase of automatic wire stripper crimper machine needs to master the skills. There are so many equipment in the market that many people find it is difficult to purchase it. So, how can we know the quality of the wire crimping machine? We... read more
23
Jun
Fully automatic wire crimping machine combines the structural advantages of single-end high-speed automatic wire crimping machine. Double-end single-end crimping terminal, super high speed, single-end crimping can reach 7000 or so pcs per hour, the total length of ultra-short wire incl. cutting and crimping terminal is 9MM. Double-ends crimping 5000pcs or so per hour, ultra-short wire cutting wire and crimping is 40MM or so. The automatic double-ends wire crimping machine mainly adopts imported original parts to complete stripping, cut to length, terminal crimping, half-stripping, twisting and other precise movements, simple operation and stable performance. Suitable for cutting AWG#30-AWG#18 wire.
Simple disposal of sudden abnormality by fully automatic wire crimping machine
As an advanced intelligent equipment, fully automatic wire crimping machine is widely used in wire harness processing industry. Fully automatic wire crimping machine not only has high processing speed, but also has high processing accuracy. It is an indispensable mechanical equipment in wire harness processing industry. Advanced equipment also marks the development of enterprises. Wire harness industry uses intelligent automatic... read more
09
Apr
1, poor insulation
The function of the insulator is to keep the contact part in the correct position, and make the contact between the contact part and the complex part. Therefore, the insulation must have excellent electrical properties, mechanical properties and mechanical properties of the... read more
25
Nov
Before using the automatic wire terminator, it is beneficial to know more about its common faults. When there is a fault, we can quickly know the cause of the fault and take effective measures to solve it in the first time. Today, we will talk... read more
09
Apr
Generally speaking, semi automatic wire terminator in normal work, there are several common problems. One is the poor contact terminals and insulation, as well as poor fixed.
1.) the phenomenon of poor contact the metal conductor inside the terminal is the core part of the terminal, which... read more
25
Oct
Analysis of poor contact problem of wire terminal crimping machine:
For machines, poor contact has always been one of the main causes of failure, ranging from small size like mobile phones to big one like computers, wire terminal crimping machines, or aviation equipment and etc.... read more
17
Jun
What causes bad contact of wire crimping machine? For machines, poor contact has always been one of the main causes of failure, from small mobile phones, large computers, larger end-to-end sub-machines or aviation equipment. Since this problem is so important, we must pay attention to it. Let Fortune Sky wire crimping machine manufacturer analyze the bad contact problem of wire crimping machine today.
For a computer, the most common malfunction is the memory chip. For a wire crimping machine, the most common malfunction is the metal conductor inside the terminal. This part is the core part of the terminal. It transmits the voltage, current or signal from external wires or cables to the contacts corresponding to its matching connectors.
Because of its importance, the wire crimping machine is required to have stable and reliable contact and good conductivity. So what factors will cause poor contact of wire crimping machine contact structure?
In fact, this is a common factor, such as excessive processing size, unreasonable surface treatment technology such as heat treatment and plating, poor storage environment, poor and improper use and operation, etc., may make contact parts and coordination parts of automatic wire crimping machine poor contact.
Common fatal faults at terminals?
1. Poor contact
The metal conductor inside the terminal is the core part of the terminal. It transmits the voltage, current or signal from the external wire or cable to the contacts corresponding to its matching connector. Therefore, the contact parts must have excellent structure, stable and reliable contact retention and good conductivity. Due to the unreasonable structure design, wrong material selection, unstable die, excessive processing size, rough surface, unreasonable surface treatment process such as heat treatment and electroplating, improper assembly, poor storage and use environment and improper operation, all of these will cause poor contact at the contact and coordination parts of the contact parts.
2. Poor insulation
The function of insulator is to keep the contacts in the correct position, and to protect the contacts from the contacts and the shells from each other by insulating the conveyor. Therefore, insulators must have excellent electrical performance, conveyor protection mechanical performance and process forming performance. Especially with the wide use of high density and miniaturized terminals, the effective wall thickness of insulators becomes thinner and thinner. This puts forward more stringent requirements for insulation materials, precision of injection moulds and moulding technology. Due to the existence of metal redundancy, surface dust, flux and other contaminations on the surface or inside of insulators, the amalgamation of organic material precipitates and harmful gas adsorption film with surface water film to form ionic conductive channels, moisture absorption, long mold, aging of insulating materials and other reasons, will cause short circuit, leakage, breakdown, low insulation resistance and other bad insulation phenomena.
3. Poor fixation
Insulators not only play an insulating role, but also provide precise centering and protection for extended contacts. They also have the functions of installation, positioning and locking and fixing on equipment. Poor fixing, light impact on contact reliability, resulting in instantaneous power failure, the serious is product disintegration. Disintegration refers to the abnormal separation between plugs and sockets and between pins and sockets caused by unreliable structure due to material, design, process and other reasons, which will result in serious consequences of power transmission and signal control interruption of computer stripper in control system. Due to unreliable design, wrong material selection, improper selection of forming process, poor quality of heat treatment, die, assembly, welding and other processes, inadequate assembly will cause poor fixation.
In addition, due to coating peeling, corrosion, bruising, plastic shell flying edge, rupture, rough contact parts processing, deformation and other reasons caused by poor appearance, due to positioning and locking with poor size, poor consistency of processing quality, total separation force and other reasons caused by poor interchange, is also a common disease, frequently occurring. These kinds of faults can be found and eliminated in time in the process of inspection and use.
read more